manualshive.com logo in svg

Air Techniques A/T2000 XR, Service Manual, Page: 22 / 60

Share
Download
Air Techniques A/T2000 XR Service Manual Download Page 22

22

Bath Temp

(°

F)

Thermistor

Resistance

60

7658

61

7642

62

7274

63

7089

64

6911

65

6739

66

6569

67

6406

68

6245

69

6092

Bath Temp

(°

F)

Thermistor

Resistance

70

5941

71

5797

72

5655

73

5516

74

5382

75

5251

76

5125

77

5000

78

4882

79

4765

Bath Temp

(°

F)

Thermistor

Resistance

80

4651

81

4540

82

4432

83

4328

84

4225

85

4126

86

4029

87

3936

88

3844

89

3755

Bath Temp

(°

F)

Thermistor

Resistance

90

3668

91

3583

92

3501

93

3420

94

3343

95

3266

96

3193

97

3120

98

3050

99

2982

Notes:

To accurately measure the thermistor’s resistance (Ohms), immerse the probe into a bath of water with a
known temperature.  A minimum of 2 minutes immersion time is required to acclimate the probe to the
bath.  Measure the resistance at the connector points.

Any other resistance value found at the corresponding temperature which is not within the high and low
limit curves is considered Out of Spec and deemed faulty.

THERMISTOR RESISTANCE CHART

Summary of Contents for A/T2000 XR





























































Reviews:

No comments