Air Live WN-350R User Manual Download Page 164

Page: 164 / 176

3. Advanced Functions

155

WN-350R User’s Manual

3.6. Firmware Upgrade

The system software used by this router is called as ‘firmware’, just like any

applications on your computer, when you replace the old application with a

new one; your computer will be equipped with new function. You can also use

this firmware upgrade function to add new functions to your router, even fix the

bugs of this router.

To upgrade firmware, please follow the following instructions:

Please click ‘Tool’ located at the upper-right corner of web management

interface, then click ‘Firmware Upgrade’ on the left of web management

interface, then the following message will be displayed on your web browser:

Please click ‘Next’, and the following message will be displayed:

Summary of Contents for WN-350R

















































































































































































Search results

Summary of Contents for WN-350R

Reviews:

Related manuals for WN-350R

Brands by name

Popular brands

Air Live WN-350R, User Manual

Search results

Summary of Contents for WN-350R

Reviews:

Related manuals for WN-350R

Brands by name

Popular brands