Air Live WN-350R User Manual Download Page 129

Page: 129 / 176

3. Advanced Functions

WN-350R User’s Manual

120

Delete (11):

Please select a virtual server mapping by clicking the

‘Select’ box of the mapping, then click ‘Delete Selected’

button to remove the mapping. If there’s no existing

mapping, this button will be grayed out.

Delete All (12):

Delete all mappings existed in virtual server table.

Reset (13):

Unselect all mappings.

After you finish with all settings, please click ‘Apply’ (14) button and the

following message will be displayed on your web browser:

Please click ‘Continue’ to back to previous setup menu; to continue on other

setup procedures, or click ‘Apply’ to reboot the router so the settings will take

effect (Please wait for about 30 seconds while router is rebooting).

If you want to reset all settings in this page back to previously-saved value,

please click ‘Cancel’ button.

Summary of Contents for WN-350R

















































































































































































Search results

Summary of Contents for WN-350R

Reviews:

Related manuals for WN-350R

Brands by name

Popular brands

Air Live WN-350R, User Manual

Search results

Summary of Contents for WN-350R

Reviews:

Related manuals for WN-350R

Brands by name

Popular brands