Air Live WN-350R User Manual Download Page 65

Page: 65 / 176

2. System and Network Setup

WN-350R User’s Manual

MTU (5):

Please input the MTU value of your network connection

here. If you don’t know, you can use default value.

BEZEQ-ISRAEL (6): If you are connecting to the BEZEQ network in Israel.

Please enable this function.

Connection type (7): Please select the connection type of Internetconnection

you wish to use, please refer to section 2-5-3 for

detailed descriptions.

Idle Time Out (8):

Please input the idle time out of Internet connection you

wish to use, and refer to section 2-5-3 for detailed

descriptions.

When you finish with all settings, please click ‘Apply’ (9) button and the

following message will be displayed on your web browser:

Please click ‘Continue’ to back to previous setup menu; to continue on other

setup procedures, or click ‘Apply’ to reboot the router so the settings will take

effect (Please wait for about 30 seconds while router is rebooting).

If you want to reset all settings in this page back to previously-saved value,

please click ‘Cancel’ button.

Summary of Contents for WN-350R

















































































































































































Search results

Summary of Contents for WN-350R

Reviews:

Related manuals for WN-350R

Brands by name

Popular brands

Air Live WN-350R, User Manual

Search results

Summary of Contents for WN-350R

Reviews:

Related manuals for WN-350R

Brands by name

Popular brands