Air Live WN-350R User Manual Download Page 86

Page: 86 / 176

2. System and Network Setup

WN-350R User’s Manual

2.7.1. Basic Wireless Settings

Please click ‘Wireless’ menu on the left of web management interface, then

click ‘Basic Settings’, and the following message will be displayed on your web

browser:

This wireless router can be work in 6 modes:

Access Point: Standard wireless AP .

Station-Infrastructure: Configure the router to Ethernet device such us

TV, Game player, HDD&DVD to enable the Ethernet device be a

wireless station.

AP Bridge-Point to Point: Connect this router with another wireless

router, to expand the scope of network.

AP Bridge-Point to Multi-Point: Connect this router with up to four other

wireless routers, to expand the scope of network.

2
3
4
5

Summary of Contents for WN-350R

















































































































































































Search results

Summary of Contents for WN-350R

Reviews:

Related manuals for WN-350R

Brands by name

Popular brands

Air Live WN-350R, User Manual

Search results

Summary of Contents for WN-350R

Reviews:

Related manuals for WN-350R

Brands by name

Popular brands