Air Live WN-350R User Manual Download Page 67

Page: 67 / 176

2. System and Network Setup

WN-350R User’s Manual

Idle Time Out (6):

Please input the idle time out of Internet connection you

wish to use, and refer to section 2-5-3 for detailed

descriptions.

When you finish with all settings, please click ‘Apply’ (7) button and the

following message will be displayed on your web browser:

Please click ‘Continue’ to back to previous setup menu; to continue on other

setup procedures, or click ‘Apply’ to reboot the router so the settings will take

effect (Please wait for about 30 seconds while router is rebooting).

If you want to reset all settings in this page back to previously-saved value,

please click ‘Cancel’ button.

Summary of Contents for WN-350R

















































































































































































Search results

Summary of Contents for WN-350R

Reviews:

Related manuals for WN-350R

Brands by name

Popular brands

Air Live WN-350R, User Manual

Search results

Summary of Contents for WN-350R

Reviews:

Related manuals for WN-350R

Brands by name

Popular brands