Agrison 110HP ULTRA Operation Manual Download

Page: 54 / 91

Accessories, Spare Parts and Quick-Wearing Parts

-41-

3. Accessories, Spare Parts and Quick-Wearing Parts

3.1 Accessories

The accessories of the tractor include fan heater, pendulum type draw bar, etc.

3.1.1 Fan heater (optional)

The fan heater on the tractor is installed in the front upper part in the driver’s cab. The fan

heater switch is installed on the fan heater. The fan heater will be in operation as long as the fan

heater switch is turned on, to make working temperature comfortable in cab.

When it needs to be ventilated in the cab (especially in summer), nothing remains but to shut

off the hot circulating water outlet valve of the fan heater on engine and turn on the fan heater

switch; here the fan of fan heater will be in operation.

The two small flop gates on both left and right sides of fan heater are used to regulate air

stream circulation.

3.1.2 Pendulum type draw bar (optional)

The pendulum type draw bar is only used in trailed implement. Rear end of the draw bar is

connected with farm implement by draw pin. The draw bar can swing transversely and it is

relatively easy to connect with farm implement. The draw bar in operation can swing left and right,

but when the tractor draws farm implement to go backward, the locating pin must be inserted in

the hole of draw plate to prevent draw bar swinging.

The height of traction point can be changed by turning draw bar to make traction height

suitable to the farm implement.

Warning:

For the tractor with fan heater or air conditioner installed, anti-freezing

solution must be applied to the cooling system of engine to protect fan heater

or air conditioner from frost crack.

Summary of Contents for 110HP ULTRA




























































































Search results

Summary of Contents for 110HP ULTRA

Reviews:

Related manuals for 110HP ULTRA

Brands by name

Popular brands

Agrison 110HP ULTRA, Operation Manual

Search results

Summary of Contents for 110HP ULTRA

Reviews:

Related manuals for 110HP ULTRA

Brands by name

Popular brands