Agrison 110HP ULTRA Operation Manual Download

Page: 21 / 91

Appendix

Connecting bolts between engine and clutch

M10

65-79

Large bevel gear bolts

M14×1.5

160-200

Connecting bolts between driving shaft housing and rear axle

housing

M14×1.5

160-200

Connecting bolts between driving wheel hub and wheel plate

M18×1.5

397-457

Connecting bolts between front wheel hub and wheel plate

M16×1.5

200-260

Connecting bolts between front support and engine

M16

182-245

Left and right steering arm nuts

M14×1.5

140-205

Connecting nuts between steering circle and steering column

M16×1.5

130-150

Connecting bolts between oil cylinder head and lifter housing

M18×1.5

200-260

Steering oil cylinder end fixed pin nuts

M18×1.5

300-330

Connecting bolts between front rear swing pin bracket and front

bracket

M18×1.5

182-245(392)

Connecting bolts between power adjusting seat and rear axle

housing

M12×1.5

90-110

Connecting bolts and nuts between lift housing and rear axle

housing

M12×1.5

90-110

Note: main bolts and nuts of tractor must be tightened with torque wrench.

10.3 Implements and accessories for wheel tractor

Table 10-4 implements and accessories for wheel tractor

Type

Matching

Implements

Model

Main Technical Parameter

Plough

machinery

Three-share

mounted plow

1L-335

Plowing depth 22-28cm

Three-share

turn mounted

plow

1LF-335

Three-share

amplitude

mounted plow

1LT-335

Plowing depth 22-28cm

Five-share

mounted plow

1L-525

Plowing depth 1-24cm

Six-share

mounted plow

1L-627

Plowing depth 16-20cm

Seven-share

mounted plow

1L-727

Plowing depth 16-20cm

Summary of Contents for 110HP ULTRA




























































































Search results

Summary of Contents for 110HP ULTRA

Reviews:

Related manuals for 110HP ULTRA

Brands by name

Popular brands

Agrison 110HP ULTRA, Operation Manual

Search results

Summary of Contents for 110HP ULTRA

Reviews:

Related manuals for 110HP ULTRA

Brands by name

Popular brands