Agrison 110HP ULTRA Operation Manual Download

Page: 14 / 91

Safety Notes

-7-

1.2

Safety warning signs

Notes:

The safety warning signs must be kept clear and legible; if they are dirty, wash them

with soap water, or clean them with soft rag;

2. If the safety warning signs are lost or unclear, contact the distribution department or

manufacturer in time for replacement;

3. If the parts with safety warning signs are to be replaced, then the safety warning

signs also shall be replaced when the parts are replaced;

4. The contents of safety warning signs involve personal safety, so they shall be well

implemented.

Meaning:

It is forbidden to sit at the non-passenger position of

the tractor, or falling accident may occur!

Application position:

Middle position of left and right fender boards.

Figure1-1 Safety warning signs

Meaning:

Certain distance shall be kept with the hot machine

surface during the machine operation, or scald

accident may be caused!

Application position: Outside of silencer.

Figure1-2 Safety warning signs

Summary of Contents for 110HP ULTRA




























































































Search results

Summary of Contents for 110HP ULTRA

Reviews:

Related manuals for 110HP ULTRA

Brands by name

Popular brands

Agrison 110HP ULTRA, Operation Manual

Search results

Summary of Contents for 110HP ULTRA

Reviews:

Related manuals for 110HP ULTRA

Brands by name

Popular brands