Agilent Technologies U1401B User'S Manual And Service Manual Download

Page: 33 / 181

Getting Started

U1401B User’s and Service Guide

The display at a glance

To view the full display (with all segments illuminated),
press

while turning the rotary switch from OFF to any

non- OFF position. After you are done viewing the full
display, press any key to resume the normal function,
depending on the rotary switch position.

The instrument will then enter power save mode if the auto
power- off (

) feature is enabled. To wake the

instrument up, perform the following steps:

Turn the rotary switch (knob) to the OFF position;

Then turn the rotary switch to any position other than
square wave output and press any key.

Figure 1-6

Full display

Summary of Contents for U1401B






















































































































































































Search results

Summary of Contents for U1401B

Reviews:

Related manuals for U1401B

Brands by name

Popular brands

Agilent Technologies U1401B, User'S Manual And Service Manual

Search results

Summary of Contents for U1401B

Reviews:

Related manuals for U1401B

Brands by name

Popular brands