Agilent Technologies U1401B User'S Manual And Service Manual Download Page 116

Page: 116 / 181

U1401B User’s and Service Guide

Application Examples

Diode Test

A good diode allows current to flow in one direction only.

To test a diode, turn the circuit power off, remove the diode
from the circuit, and proceed as follows:

Turn the rotary switch to the

position.

Connect the red and black probe leads to the positive and
negative input terminals respectively.

Probe the positive (anode) side of the diode with the red
lead, and the negative (cathode) side with the black lead.

Reverse the probe leads and measure the voltage across
the diode again.

If the diode is:

•

Good: In step 3, a forward voltage drop typically from
0.3 V to 0.8 V is indicated (the instrument can display
diode voltage drops up to approximately 2.1 V)
accompanied by a beep. In step 4,

is indicated.

•

Shorted: A voltage drop of nearly 0 V is indicated in
both directions, and the instrument will beep
continuously.

•

Open:

is indicated in both directions.

N O T E

The cathode of a diode is the side indicated with band(s).

Summary of Contents for U1401B






















































































































































































Search results

Summary of Contents for U1401B

Reviews:

Related manuals for U1401B

Brands by name

Popular brands

Agilent Technologies U1401B, User'S Manual And Service Manual

Search results

Summary of Contents for U1401B

Reviews:

Related manuals for U1401B

Brands by name

Popular brands