Agilent Technologies U1401A User'S Manual And Service Manual Download

Page: 25 / 177

Getting Started

U1401A User’s and Service Guide

Product Overview

Slide switch

The slide switch has the following positions:

•

Charge

: Select this position to charge the batteries. Use the

AC adapter provided to charge this instrument.

•

: Select this position to enable only the measurement

functions.

•

M/S

: Select this position to enable both the measurement

and source functions.

Figure 1-1

The slide switch

Table 1-2

Slide switch functions

No.

Description

Function

External AC
adapter jack

Allows an external AC adapter to be connected to
provide power or charge the batteries.

CHARGE

Charges the batteries with an external AC adapter.

Enables only the measurement functions.

M/S

Enables both measurement and source functions.

Summary of Contents for U1401A


















































































































































































Search results

Summary of Contents for U1401A

Reviews:

Related manuals for U1401A

Brands by name

Popular brands

Agilent Technologies U1401A, User'S Manual And Service Manual

Search results

Summary of Contents for U1401A

Reviews:

Related manuals for U1401A

Brands by name

Popular brands