Agilent Technologies U1401A User'S Manual And Service Manual Download Page 43 | Manualshive

Page: 43 / 177

background image

Getting Started

1

U1401A User’s and Service Guide

23

Remote Communication

The U1401A has a bidirectional (full duplex) communication
capability that makes it very easy to transfer data from the
instrument to a PC.

The required accessory for this feature is an optional
IR- USB cable and the application software in the
accompanying CD.

To communicate with the personal computer through remote
communication:

1

Set up the communication parameters of the instrument
and the personal computer you are using. The default
values for baud rate, parity, data bits, and stop bit for the
instrument are 9600, n, 8, and 1 respectively.

2

Make sure that the USB driver and the Agilent data logger
software has been installed on your computer.

3

Attach the optic side of the cable to the communication
port on the instrument. Make sure that the text side is
facing upwards. See

Figure 1- 10

on page 25.

4

Plug the other end of the USB cable terminal into the
USB port of your personal computer.

5

Use the data transfer software to retrieve the data that
you need.

6

Press the flaps to remove the cable from the
communication port of the instrument. See

Figure 1- 11

on

page 25.

7

It is not recommended to remove the connector cover of
the IR- USB cable. But sometime, while pressing the flap
to unplug the cable, the connector cover may come off
accidentally as shown in

Figure 1- 11

on page 25. To

N O T E

You will need to download the Agilent data logger software from Agilent’s
website in order to use this feature. Please go to:

http://www.agilent.com/find/hhTechLib

to download the software.

«
...
41
42
43
44
45
...
»

Summary of Contents for U1401A


















































































































































































Reviews:

No comments

Related manuals for U1401A

Brand: Giacomini Pages: 83

Brand: Casio Pages: 37

Brand: KYOWA Pages: 47

Brand: Fluke Pages: 18

Brand: Agilent Technologies Pages: 356

MadgeNET RFTemp2000A

Brand: MadgeTech Pages: 16

Brand: National Instruments Pages: 75

Brand: Vega Pages: 30

Brand: REED Pages: 16

Brand: Lascar Pages: 6

EasyLog EL-PDF-1 Series

Brand: Lascar Electronics Pages: 2

Brand: BART Pages: 38

Brand: scigiene Pages: 66

Brand: sebaKMT Pages: 33

DaqBook/3000USB

Brand: IOtech Pages: 66

Ixxat CANnector Log

Brand: HMS Networks Pages: 38

A73 addWAVE Series

Brand: Adcon Pages: 64

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands