Agilent Technologies U1401A User'S Manual And Service Manual Download Page 33

Page: 33 / 177

Getting Started

U1401A User’s and Service Guide

The display at a glance

To view the full display (with all segments illuminated),
press

while turning the rotary switch from OFF to any

non- OFF position. After you are done viewing the full
display, press any key to resume the normal function,
depending on the rotary switch position.

The instrument will then enter power save mode if the auto
power- off (

) feature is enabled. To wake the

instrument up, perform the following steps:

Turn the rotary switch (knob) to the OFF position;

Then turn the rotary switch to any position other than
square wave output and press any key.

Figure 1-6

Full display

Summary of Contents for U1401A


















































































































































































Search results

Summary of Contents for U1401A

Reviews:

Related manuals for U1401A

Brands by name

Popular brands

Agilent Technologies U1401A, User'S Manual And Service Manual

Search results

Summary of Contents for U1401A

Reviews:

Related manuals for U1401A

Brands by name

Popular brands