manualshive.com logo in svg

Agilent Technologies E8363BU/CU-068, Installation Note, Page: 20 / 46

Share
Download
Agilent Technologies E8363BU/CU-068 Installation Note Download Page 20

20

  

                                                                                                                            

  

Installation Note E8364-90023

Step 7. Remove the Old Bottom Side Hardware and Cables

•

Remove the Existing Configurable Test Set Cables

•

Remove the A17 LOMA 10

•

Remove the A18 MA 20

•

Remove the A22 Switch/Splitter

•

Remove the A23 and A24 Detectors

•

Remove the A27, A28, A29, and A30 First Converters (Mixers)

•

Remove the A25 and A26 Test Port Couplers

•

Remove the A20 LODA (5087-7129)

Remove the Existing Configurable Test Set Cables

1. Using a 5/16-inch wrench, remove the hex nuts from all 12 front panel connectors (item 

①

). Remove the lock washers. Retain both the hex nuts and lock washers for installation of 

new connectors later.

2. Using a 5/16-inch wrench, remove each of the configurable test set cables (item 

②

) from 

the analyzer. Discard these cables, they will be replaced with new ones.

Figure 9

Existing Configurable Test Set Cables Removal

Summary of Contents for E8363BU/CU-068















































Reviews:

No comments