manualshive.com logo in svg

Agilent Technologies E8363BU/CU-068, Installation Note, Page: 12 / 46

Share
Download
Agilent Technologies E8363BU/CU-068 Installation Note Download Page 12

12

  

                                                                                                                            

  

Installation Note E8364-90023

Step 2.  Remove the Outer and Inner Covers

Remove the Outer Cover

CAUTION

This procedure is best performed with the analyzer resting on its front 
handles in the vertical position. 

Do not place the analyzer on its front panel 

without the handles

. This will damage the front panel assemblies.

1. Disconnect the power cord (if it has not already been disconnected).

2. Using a T-20 TORX driver, remove the strap handles (item 

④

) by loosening the screws 

(item

⑤

) on both ends until the handle is free of the analyzer.

3. Using a T-20 TORX driver, remove the four rear panel feet (item 

①

) by removing the center 

screws (item 

②

).

4. Slide the four bottom feet (item 

③

) off the cover.

5. Slide the cover off of the frame.

Figure 2

Outer Cover Removal

NOTE

The figure above shows the E8364B front panel and floppy disk drive. The 
E8363C and E8364C front panel have a slightly different appearance and 
does not include a floppy disk drive. 

Summary of Contents for E8363BU/CU-068















































Reviews:

No comments