manualshive.com logo in svg

Agilent Technologies E8363BU/CU-068, Installation Note, Page: 5 / 46

Share
Download
Agilent Technologies E8363BU/CU-068 Installation Note Download Page 5

Installation Note E8364-90023                                                                                                                         

 

5

Downloading the Online PNA Service Guide 

To view the online Service Guide for your PNA model number, use the following steps:

1. Go to

 

www.agilent.com

2. In the Search box, enter the model number of the analyzer (Ex: E8363B) and click 

Search

.

3. Click 

Technical Support > Manuals

.

4. Click 

Service Manual

.

5. Click the service guide title to load the PDF file.

6. When the PDF of the Service Guide is displayed, scroll through the Contents section 

bookmarks to locate the information needed. 

Protecting Your Workspace from Electrostatic Discharge

For information, click on the Chapter 1 PDF bookmark, 

“Electrostatic Discharge Protection”

 

in the online Service Guide

1

.

ESD Equipment Required for the Installation

Tools Required for the Installation 

CAUTION

Use a 5/16-in torque wrench set to 10 in-lbs on all cable connections except the 
front panel and some rear panel cable connectors. Torque these connections to 
21 in-lb.

1. See 

“Downloading the Online PNA Service Guide” on page 5

.

Description

Agilent Part Number

ESD grounding wrist strap

9300-1367

5-ft grounding cord for wrist strap

9300-0980

2 x 4 ft conductive table mat and 15-ft grounding wire

9300-0797

ESD heel strap (for use with conductive floors)

9300-1308

Description

Qty

Part Number

T-10 TORX driver - set to 9 in-lbs (1.02 N.m)

1

N/A

T-20 TORX driver - set to 21 in-lbs (2.38 N.m)

1

N/A

5/16-in (8 mm) nutsetter or open end torque wrench - set 
to 10 in-lbs (1.13 N.m)

1

N/A

5/16-in (8 mm) nutsetter or open end torque wrench - set 
to 21 in-lbs (2.38 N.m)

1

N/A

1-inch torque wrench - set to 72 in-lbs (8.15 N.m)

N/A

1-inch torque wrench 
(set to 72 in-lbs)

Summary of Contents for E8363BU/CU-068















































Reviews:

No comments