manualshive.com logo in svg

Agilent Technologies E8363BU/CU-068, Installation Note, Page: 43 / 46

Share
Download
Agilent Technologies E8363BU/CU-068 Installation Note Download Page 43

Installation Note E8364-90023                                                                                                                         

 

43

Reinstall the Outer Cover

CAUTION

This procedure is best performed with the analyzer resting on its front 
handles in the vertical position. 

Do not place the analyzer on its front panel 

without the handles

. This will damage the front panel assemblies.

1. Slide the cover onto the frame.

2. Using a T-20 TORX driver, install the four rear panel feet (item 

①

) by installing the center 

screws (item 

②

).

3. Slide the four bottom feet (item 

③

) onto the cover.

4. Using a T-20 TORX driver, install the strap handles (item 

④

) by tightening the screws 

(item

⑤

) on both ends.

Figure 30

 Outer Cover Reinstallation

NOTE

The figure above shows the E8364B front panel and floppy disk drive. The 
E8363C and E8364C front panel have a slightly different appearance and 
does not include a floppy disk drive. 

Summary of Contents for E8363BU/CU-068















































Reviews:

No comments