manualshive.com logo in svg

Agilent Technologies E8363BU/CU-068, Installation Note, Page: 4 / 46

Share
Download
Agilent Technologies E8363BU/CU-068 Installation Note Download Page 4

4

  

                                                                                                                            

  

Installation Note E8364-90023

Getting Prepared

To successfully install this upgrade kit, you will need the following:

• A license key - refer to 

“License Key Redemption”

 below.

• A PDF copy or a paper copy of the PNA Service Guide - refer to 

“Downloading the Online 

PNA Service Guide” on page 5

.

• An ESD-safe work area - refer to 

“Protecting Your Workspace from Electrostatic 

Discharge” on page 5

.

• Correct tools - refer to 

“Tools Required for the Installation” on page 5

.

• Enough time - refer to 

“About Installing the Upgrade Kit” on page 6

.

• Test equipment for the post-upgrade adjustments. Refer to 

“Test Equipment Required for 

Post-Upgrade Adjustments” on page 11

.

License Key Redemption

NOTE

The enclosed Option Entitlement Certificate is a receipt, verifying that you 
have purchased a licensed option for the PNA of your choice. You must now 
use an Agilent Web page to request a license key for the instrument that 
will receive the option.

To enable the option product, you must request a license key from: 

http://www.agilent.com/

find/softwarelicense. 

To complete the request, you will need to gather the following 

information:

• From the certificate

❏

Order number

❏

Certificate number

• From your instrument

❏

Model number

❏

Serial number

❏

Host ID

The instrument information is available on the network analyzer – on the analyzer’s 

Help

 

menu, click 

About Network Analyzer

.

If you provide an email address, Agilent will promptly email your license key. Otherwise, you 
will your receive your license key via postal mail.

Summary of Contents for E8363BU/CU-068















































Reviews:

No comments