manualshive.com logo in svg

Agilent Technologies E8363BU/CU-068, Installation Note, Page: 26 / 46

Share
Download
Agilent Technologies E8363BU/CU-068 Installation Note Download Page 26

26

  

                                                                                                                            

  

Installation Note E8364-90023

Remove the A25 and A26 Test Port Couplers

1. Using a 1-inch wrench, remove the test port coupler nuts (item 

②

) from the front panel. 

Retain the test port coupler nuts for reinstallation later.

CAUTION

Be careful not to damage the center pins of the semirigid cables. Some flexing of 
the cables is necessary to remove the assembly. Do not over-bend them.

2. Remove the A25 and A26 test port couplers from the analyzer. Observe the 

CAUTION

 above.

Figure 15 A25 and A26 Test Port Couplers Removal

Remove the A20 LODA (5087-7129)

For instructions, click the Chapter 7 PDF bookmark "Removing and Replacing the A20 

LODA" in the online Service Guide

1

.

1. See 

“Downloading the Online PNA Service Guide” on page 5

 .

Summary of Contents for E8363BU/CU-068















































Reviews:

No comments