manualshive.com logo in svg

Agilent Technologies E8363BU/CU-068, Installation Note, Page: 25 / 46

Share
Download
Agilent Technologies E8363BU/CU-068 Installation Note Download Page 25

Installation Note E8364-90023                                                                                                                         

 

25

Remove the A27, A28, A29, and A30 First Converters (Mixers)

1. Using a 5/16-inch wrench, disconnect the four remaining semirigid cables (item 

①

) from 

the mixers and the four flexible cables (item 

②

).

2. Using a T-10 TORX driver, remove the four mounting screws (item 

③

). Retain the 

mounting screws for reinstallation later.

CAUTION

Be careful not to damage the center pins of the semirigid cables. Some flexing of 
the cables is necessary to remove the assembly. Do not over-bend them.

3. Remove the mixer bracket with all four mixers attached and disconnect the ribbon cable 

(item 

④

). Observe the 

CAUTION

 above. Set this item aside for modification later.

Figure 14 A27, A28, A29, and A30 First Converters Removal

Summary of Contents for E8363BU/CU-068















































Reviews:

No comments