Agilent Technologies 929-0022, Instruction Manual

Page: 18 / 36

INSTRUCTION FOR USE
13 87-900-077-01(D)
GENERAL INFORMATION
This equipment is destined for use by professionals. The user
should read this instruction manual and any other additional
information supplied by Varian before operating the equipment.
Varian will not be held responsible for any events occurring due
to non-compliance, even partial, with these instructions, improper
use by untrained persons, non-authorised interference with the
equipment or any action contrary to that provided for by specific
national standards.
The following paragraphs contain all the information necessary to
guarantee the safety of the operator when using the equipment.
Detailed information is supplied in the appendix "Technical
Information".
This manual uses the following standard protocol:
,
WARNING!
The warning messages are for attracting the attention of the
operator to a particular procedure or practice which, if not
followed correctly, could lead to serious injury.
CAUTION
The caution messages are displayed before procedures which, if
not followed, could cause damage to the equipment.
NOTE
The notes contain important information taken from the text.
CONTROLLER DESCRIPTION
Varian’s Sublimation Controller is a titanium sublimation pumps
(TSP) controller. The unit can be factory configured to the
customer’s needs, but the configuration can be modified by the
user to adapt the controller to the different user needs.
DESCRIPTION PART NUMBER
Base Unit
Sublimation Controller set for
220 Vac input voltage 929-0023
Sublimation Controller set for
110 Vac input voltage 929-0022
Accessories
RS 232 Computer Interface
Card 929-0024
RS 422 Computer Interface
Card 929-0025
RS 485 Computer Interface
Card 929-0026
Cable for TSP pump 924-0730
Cable for Mini Ti-Ball pump 924-0752
The Sublimation Controller can control a TSP or a Mini Ti-Ball
pump type.
The Sublimation Controller can be operated in different ways:
MANUAL, AUTOMATIC, AUTOMAT/REMOTE and REMOTE
SET. In MANUAL and AUTOMATIC modes all controls are given
on front panel. In REMOTE SET and AUTOMAT/REMOTE some
controls are given on front panel and others are given by signal
through the I/O connector.
STORAGE
When transporting and storing the controller, the following
environmental requirements should not be exceeded:
−
temperature: from -20° to +70 °C
−
relative humidity: 0 - 95% (non-condensing)
PREPARATION FOR INSTALLATION
The Sublimation Controller is supplied in a special protective
packing; If this shows signs of damage which may have occurred
during transport, contact your local sales office.
When unpacking the controller, be sure not to drop it and avoid
any kind of sudden impact or shock vibration to it.
Do not dispose of the packing materials in an unauthorized
manner. The material is 100% recyclable and complies with EEC
Directive 85/399.
Controller packing
The Sublimation Controller is factory set for follows input
voltages:
•
model 929-0023 set to 220 Vac (input voltage 180 to 265
Vac).
•
model 929-0022 set to 120 Vac (input voltage 90 to 130
Vac).
If a change in line voltage operation is desired, proceed as
follows;
−
Switch off the Sublimation Controller and unplug the power
cord from the wall socket.
−
On the rear panel pull off the fuse cover, the unplug the
voltage selector.
−
Rotate the voltage selector until the desired voltage appears
towards the external part of the controller.
CAUTION
If the line voltage pass from 220-240 Vac to 100-120 Vac, or
viceversa, the power cord and the fuses MUST be changed also.
For 220-240 Vac the fuses must be T6.3A and for 100-120 Vac
must be T10A.
−
If necessary, change the fuses and the power cord. If power
cord must be changed, rewire as follows:
blue = neutral
brown = phase
yellow-green = ground
−
Insert the voltage selector, then repositioning the fuse cover.
−
Plug the power cord into wall socket.