8
za, funzionante ad R407C, ed azionato da un motore
elettrico a due poli con protezione termo-amperometrica,
montato su supporti antivibranti;
-
il modello CWX 2667 T
(per alimentazione trifase) è dota-
to di un apposito relay (RPF) che verifica la sequenza
delle fasi, per proteggere il compressore dal possibile fun-
zionamento con sequenza fasi invertita;
-
il condensatore
è del tipo a piastre, in acciaio inossidabile;
-
la valvola pressostatica
per la regolazione della pressione
di condensazione e del consumo d'acqua;
-
il pressostato di alta pressione
, a norme TÜV, di tipo
miniguard a taratura fissa;
-
il pressostato di bassa pressione
, per la protezione
dell’evaporatore dell’Idrosplit in caso di funzionamento
anomalo;
-
la presa di alta pressione.
A corredo è fornito un kit di raccordi e tappi da collegare
esternamente all'unità per lo scarico dell’impianto in caso
di rischio di gelo.
UNITÀ MOTOCONDENSANTE
RAFFREDDATA AD ARIA ( CX )
Disponibile in due grandezze (CX 1167 e CX 2667) per
l’abbinamento al modulo ID 51. La grandezza 2667 è
disponibile anche in versione trifase (CX 2667 T).
Il mobile di copertura è in lamiera di acciaio zincato, sotto-
posta a trattamento di passivazione, con verniciatura a pol-
veri per la protezione dagli agenti atmosferici.
All’interno dell’unità sono alloggiati:
-
il circuito frigorifero
, realizzato in tubo di rame ricotto,
saldato con lega d’argento e provvisto di un organo di
laminazione del tipo a capillare.
-
il compressore
, ermetico rotativo ad alta efficienza, fun-
zionante ad R 407C, azionato da un motore elettrico con
protezione termo-amperometrica, e montato su supporti
elastici antivibranti. Il modello CX 2667 T (per alimenta-
zione trifase) è dotato di un apposito relay (RPF) che veri-
fica la sequenza delle fasi, per proteggere il compressore
dal possibile funzionamento con sequenza fasi invertita;
-
la batteria di scambio termico
, costituita da tubi di rame
rigati internamente ed alette in alluminio di tipo turbolen-
ziato, bloccate mediante espansione meccanica dei tubi;
-
il ventilatore
, di tipo elicoidale con motore elettrico
monofase, è direttamente accoppiato e montato su sup-
porti antivibranti. Il gruppo ventilante è provvisto di gri-
glia di protezione secondo norme CEI 107-34.
-
il pressostato di bassa pressione
, per la protezione
dell’evaporatore dell’Idrosplit in caso di funzionamento
anomalo;
SCHEDA ELETTRONICA
Dotata di microprocessore, è situata nella parte inferiore del
modulo ID e svolge le seguenti funzioni:
- gestione della commutazione stagionale. All’avviamento,
la valvola a tre vie si commuta in posizione estiva, dopo
di che viene avviata la pompa, e per ultimo viene dato il
consenso al funzionamento del compressore;
- controllo e visualizzazione della temperatura dell’acqua
in ingresso all’evaporatore;
- gestione e visualizzazione del funzionamento in condizio-
ni di sovraccarico: dal momento in cui viene attivato il
compressore, vengono effettuati dei controlli periodici
sulla temperatura dell’acqua di ritorno dall’impianto; qua-
lora essa tenda a stabilizzarsi ad un valore al di sopra di
quello impostato, l’utente viene avvertito, tramite l’accen-
sione di una spia, che la potenza frigorifera assorbita dai
ventilconvettori attivi è superiore di quella prodotta dal
modulo ID. L'unità rimane comunque in funzione;
- partenza automatica dopo mancanza di tensione;
- controllo del numero di avviamenti orari del compressore;
- gestione e visualizzazione delle sicurezze intervenute.
with overload protection, mounted on antivibration plugs.
-
the CWX 2667 T
model (for three phase supply) is equip-
ped with a suitable relay (RPF) that checks the phase
sequence, to protect the compressor against possible
inverted phases.
-
Plate type condenser in stainless steel;
-
the flow valve
to regulate the condensing pressure and
water consumption.
- the miniguard
high pressure switch
, to TÜV standards,
with fixed calibration.
-
the low pressure switch
, to protect the evaporator on the
Idrosplit in case of abnormal operating conditions.
-
the high pressure service point.
The unit is supplied with a coupling and plug kit connected
outside the unit, to drain the unit in case of risk of freezing.
AIR COOLED CONDENSING UNIT (CX)
ID series units are available in two sizes (CX1667 and
CX2667) for coupling with the ID 51 module. Size 2667 is
also available in three-phase version (CX2667 T).
The housing is in galvanised steel sheet, passivated and then
weatherproofed with a hot powder coating.
The unit contains:
-
the refrigerant circuit
, in annealed copper pipe, welded
with silver alloy and fitted with a capillary expansion pipe.
- the high efficiency, hermetic rotary
compressor
, operating
with R407C, and powered by a two pole electric motor
with overload protection, mounted on antivibration plugs.
The CWX 2667 T model (for three phase supply) is equip-
ped with a suitable relay (RPF) that checks the phase
sequence, to protect the compressor against possible
inverted phases.
-
the heat exchange coil
, with slit aluminium fins, mechani-
cally bonded to internally grooved copper pipe
- t
he fan
: a propeller fan directly coupled to a single phase
motor and mounted on antivibration plugs. The fan group
is fitted with a guard according to CEI 107-34.
-
the low pressure switch
, to protect the evaporator on the
Idrosplit in case of abnormal operating conditions.
ELECTRONIC CARD
A card equipped with microprocessor, mounted in the
lower section of the ID module, which performs the fol-
lowing functions:
- seasonal changeover management. On start-up the three
way valve commutes to the summer position, after which
the pump is started and finally consensus is given for the
compressor to operate.
- control and display of the water inlet temperature at the
evaporator.
- management and display of operation in overload condi-
tions: from the moment the compressor is started, periodi-
cal controls are effected on the temperature of the water
returning from the plant. In the event that it tends to stabi-
lise at a value higher than the set-point, a pilot light turns
on to signal the user that the cooling capacity absorbed
by the fancoils in operation is over that produced by the
ID module. The unit nevertheless continues to operate.
- automatic start after a power cut.
- control of the number of hourly compressor starts.
- management and display of the safety trips.
ORGANI DI SICUREZZA E REGOLAZIONE •
SAFETIES AND CONTROLS
Summary of Contents for IDROSPLIT
