Aerco Innovation 1060 Page 21 User Manual Download

Page: 21 / 216

Innovation Water Heaters Installation, Operation & Maintenance Manual

CHAPTER 2 – INSTALLATION

OMM-0078_0M

AERCO International, Inc.

•

100 Oritani Dr.

•

Blauvelt, NY 10913

Page

216

GF-128

Phone: 800-526-0288

09/11/2015

WHM Ball Valve Installation

– Continued

AERCO recommends that another pipe nipple and union be attached to the valve inlet

prior to connecting the cold water supply piping.

Tighten all pipe connections after the valve is properly positioned.

Connect the 4-pin Molex connector on the valve to the mating connector on the Innovation

harness at the rear of the unit.

This completes the actuator-controlled ball valve installation.

Figure 2-3b. Innovation Water Heater Equipped With Sequencing Valve

2.6 TEST HOSE BIB CONNECTION

A Test Hose Bib connection, upstream of the shut off valve on the hot water outlet, is required

for startup and testing (Figure 2-4). The pipe diameter should be a minimum of 3/4" (1.9 cm).

The Test Hose

Bib

cannot be omitted

HEATER DRAIN VALVE

2” NPT UNION

BALL VALVE

WITH ACTUATOR

2” NPT

Summary of Contents for Innovation 1060

























































































































































































































Search results

Summary of Contents for Innovation 1060

Reviews:

Related manuals for Innovation 1060

Brands by name

Popular brands

Aerco Innovation 1060, User Manual

Search results

Summary of Contents for Innovation 1060

Reviews:

Related manuals for Innovation 1060

Brands by name

Popular brands