manualshive.com logo in svg

Aeon 350cc, Service Manual

Share
Download
Aeon 350cc Service Manual Download Page 62

ENGINE

 

 

4-62

4. Remove the thermostatic. 

 

5. Remove intake manifold and throttle body from cylinder head. 

 

6. Remove cylinder head and head gasket. 

7. If not removing the cylinder for other service, secure the 

cam chain with a wire to prevent it from falling into the 

crankcase.

 

 

CYLINDER HEAD INSPECTION 

1. Thoroughly clean cylinder head surface to remove all 

traces of gasket material and carbon.

                           

 

 

Use care not to damage sealing surface. If there is 

damage found on the cylinder head combustion 

chamber, it is recommended the component be 

replaced.

 

CYLINDER HEAD WARP INSPECTION

 

Lay a straight edge across the surface of the head at several 

different points and measure warp age by inserting a feeler 

gauge between the straight edge and the cylinder head 

surface. 

 

 

 

Summary of Contents for 350cc

































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands