63
GB
2. After several
seconds „WT
0.0 kg (0.0
lb./0:0 St:)“
will appear
on the display
(Fig. 5).
3. If the scale is not switched on you will see
“WT - - - - kg (- - - - lb., - - - - St:)” on the
LCD display.
4. Step on the scale with both feet. Distribute
your weight evenly and wait for the scale to
calculate your weight. Hold the display
vertically or horizontally over the infrared
lamp on the scale.
5. The reading on the display initially flashes
2x, then your exact weight will be shown.
When you step off the scale, the device
will switch off automatically after 20
seconds.
Programming your
personal data
Attention:
Carry out the following opera-
tions one after the other and within a few
seconds or the device will automatically
interrupt the programming mode!
1. Push the
MODE
button to switch on the
display. Wait until “WT 0.0 kg (0.0 lb./0:0
St:)” appears on the display. Use the
UNIT
button to select your preferred unit (kg, lb.
or St:).
2. Push the
MODE
button
again. Then,
push the
SET
button to
change to the
programming mode. ‘
SEt
’ appears in the
LCD display, then ‘
P
01’ (storage location)
starts to flash, and the preset symbol for
‘male’ and the preset value for the height in
cm (in.) are shown (fig. 6).
3. Select a storage location using the
P/
▲
/
ATH/
▼
buttons.
4. Then push the
SET
button and the display
changes to the next setting.
5. The symbol for ‘male’ flashes on the
display. Use the
P/
▲
/ ATH/
▼
buttons to
select a setting (‘male’ or ‘female’).
6. Push the
SET
button again to change to
the HEIGHT setting. The indication ‘170’
(67.0) flashes. Use the
P/
▲
/ ATH/
▼
but-
tons to select a value between 80 (31.5 in)
and 240 cm (94.5 in).
7. Push the
SET
button again to change to
the AGE setting. The indication ‘30’ flas-
hes. Push one of the buttons
ATH/
▼
or
P/
▲
and hold it down to run up or down
through the values in fast mode. Use the
P/
▲
/ ATH/
▼
buttons to select a value
between 6 and 100 years. If the age is set
to a value under 16 years, a child’s face
will be shown in the display next to the
male/female symbol.
8. Pushing the
SET
button again will cause
the storage location, sex, age and entered
height to be displayed for a few seconds,
then the indication changes to “WT 0.0 kg
(0.0 lb./0: 0
St:) and - - -
(HT)”. If the
scale is not
switched on
the reading
will be as
shown in Fig. 7.
a. Push the
MODE
button three times to view
all settings again. The reading must be as
shown in Fig. 6.
b. If you want to make any changes push the
MODE
button until the display reads as
shown in Fig. 6. By pushing the
P/
▲
but-
ton you change to the selection mode.
Now choose the storage location with the
settings you wish change (flashing indicati-
on) using the
P/
▲
and
ATH/
▼
buttons and
push the
SET
button. Proceed as descri-
bed in steps 4 to 6.
c. If you wait for more than 15 seconds wit-
hout changing anything the reading chan-
ges back to the time.
Your personal data is now stored in the
selected storage location.
There is an overall number of 16 storage
locations. The remaining 15 storage locati-
ons can be used to store also the personal
data of other members of your family or other
users of these scales.
(fig. 5)
(fig. 6)
(fig. 7)
PW_4914_Bed_Anl_A5_3.qxd 28.08.2007 12:30 Uhr Seite 63
Весы напольные AEG PWI 4914 FA
Купить в интернет-магазине
http://clatronic-shop.com.ua
