Advantech EKI-8500 Series User Manual Download Page 90

Page: 90 / 98

EKI-8500 Series User Manual

The following table describes the items in the PSFP SGI Status page.

4.4.4.4

FRER

4.4.4.4.1

FRER Status

The function provides an overview of the current FRER status.

Navigate to

Monitor

TSN

FRER

and click

FRER Status

The FRER Status page displays.

Figure 4.57 FRER Status

The following table describes the items in the FRER Status page.

Item

Description

SGI ID

Displays the instance parameter.

Oper Gate Enabled Displays the active (true) / inactive (false) state of the parameter.
Oper Gate States

Displays the operational value indicating an open or closed gate.

Cycle Time

Numerator

Displays the operational numerator value indicating the cycle time as

a rational number of seconds. The numerator and denominator

together represent the cycle time as a rational number.

Cycle Time

Denominator

Displays the operational denominator value indicating the cycle time

as a rational number of seconds. The numerator and denominator

together represent the cycle time as a rational number.

Cycle Time

Extension

Displays the operational value of the CycleTimeExtension parameter

in nanoseconds.

Base Time

Displays the operational value of the BaseTime paramter. The value is

a representation of a PTPtime value, consisting of a 48-bit integer

number of seconds and a 32-bit integer number of nanoseconds.

Current Time

Displays the current time, in PTPtime, as maintained by the local

system.

Config Change Time Displays the PTPtime at which the next config change is scheduled to

occur.

Config Change Error Displays the number of times that a re-configuration of the traffic

schedule has been requested with the old schedule still running and

the requested base time was in the past.

Tick Granularity

Displays the granularity of the cycle time clock, represented as an

unsigned number of tenths of nanoseconds.

Config Pending

Displays the value of the ConfigPending state machine variable.

Oper IPV

Displays the operational value of the IPV parameter.

GCL Length

Displays the operational value of the ListMax parameter.

GCL Status

Displays the link to the GCL parameter status.

Auto-refresh

Check this box to refresh the page automatically. Automatic refresh

occurs every 3 seconds.

Refresh

Click

Refresh

to refresh the page immediately.

Item

Description

Instance

Displays the FRER instance.

Oper

Displays the operational state.



Green: active



Red: disabled or internal error detected.

Summary of Contents for EKI-8500 Series



































































































Search results

Summary of Contents for EKI-8500 Series

Reviews:

Related manuals for EKI-8500 Series

Brands by name

Popular brands

Advantech EKI-8500 Series, User Manual

Search results

Summary of Contents for EKI-8500 Series

Reviews:

Related manuals for EKI-8500 Series

Brands by name

Popular brands