Advantech EKI-8500 Series User Manual Download Page 84

Page: 84 / 98

EKI-8500 Series User Manual

4.4.3

VLANs

4.4.3.1

Membership

The function provides an overview of membership status of VLAN users.

Navigate to

Monitor

VLANs

and click

Membership

The VLAN Membership Status page displays.

Figure 4.49 VLAN Membership Status

The following table describes the items in the VLAN Membership Status page.

Refresh

Click

Refresh

to refresh the page immediately.

Clear

Click to clear the statistics.

SyncCount

Displays the counter that increments every time synchronization

information is transmitted.

FollowUpCount

Displays the counter that increments every time a Follow_Up

message is transmitted.

PdelayRequestCount Displays the counter that increments every time a Pdelay_Req

message is transmitted.

PdelayResponse

Count

Displays the counter that increments every time a Pdelay_Resp

message is transmitted.

PdelayResponse

FollowUpCount

Displays the counter that increments every time a

Pdelay_Resp_Follow_Up message is transmitted.

AnnounceCount

Displays the counter that increments every time an Announce

message is transmitted.

Item

Description

Item

Description

Start from VLAN
First Page

Click the icon to display the first page.

Click the icon to display the next page in the list.

VLAN ID

Displays the VLAN ID for the port entry.

Port Members

Displays the status of the port:



Included in a VLAN



Forbidden



Forbidden and attempted included in VLAN

A row of check boxes for each port is displayed for each VLAN ID.

Select Users

Click the drop-down menu to select the VLAN users. Options:



Admin



NAS



GVRP



MVR



RMirror

Auto-refresh

Check this box to refresh the page automatically. Automatic refresh

occurs every 3 seconds.

Refresh

Click

Refresh

to refresh the page immediately.

Summary of Contents for EKI-8500 Series



































































































Search results

Summary of Contents for EKI-8500 Series

Reviews:

Related manuals for EKI-8500 Series

Brands by name

Popular brands

Advantech EKI-8500 Series, User Manual

Search results

Summary of Contents for EKI-8500 Series

Reviews:

Related manuals for EKI-8500 Series

Brands by name

Popular brands