Advantech EKI-8500 Series User Manual Download Page 80

Page: 80 / 98

EKI-8500 Series User Manual

The Detailed Port Statistics page displays.

Figure 4.43 Detailed Port Statistics

The following table describes the items in the Detailed Port Statistics page.

The following table describes the items in the Receive and Transmist Error Counters

table.

Figure 4.44 Receive and Transmit Error Counters Table

Item

Description

Rx and Tx Packets

Displays the number of received and transmitted packets.

Rx and Tx Octets

Displays the number of received and transmitted bytes. Includes FCS,

but excludes framing bits.

Rx and Tx Unicast

Displays the number of received and transmitted unicast packets.

Rx and Tx Multicast Displays the number of received and transmitted multicast packets.
Rx and Tx Broadcast Displays the number of received and transmitted broadcast packets.
Rx and Tx Pause

Displays the count of the MAC Control frames received or transmitted

on this port that have an opcode indicating a PAUSE operation.

Receive and

Transmit Size

Counters

Displays the number of received and transmitted (good and bad)

packets split into categories based on their respective frame sizes.

Receive and

Transmit Queue

Counters

Displays the number of received and transmitted packets per input

and output queue.

Refresh

Click

Refresh

to refresh the page immediately.

Clear

Click

Clear

to clear the counters for the selected port.

Auto-refresh

Check this box to refresh the page automatically. Automatic refresh

occurs every 3 seconds.

Item

Description

Rx Drops

Displays the number of frames dropped due to lack of receive buffers

or egress congestion.

Rx CRC/Alignment

Displays the number of frames received with CRC or alignment errors.

Summary of Contents for EKI-8500 Series



































































































Search results

Summary of Contents for EKI-8500 Series

Reviews:

Related manuals for EKI-8500 Series

Brands by name

Popular brands

Advantech EKI-8500 Series, User Manual

Search results

Summary of Contents for EKI-8500 Series

Reviews:

Related manuals for EKI-8500 Series

Brands by name

Popular brands