Advantech EKI-8500 Series User Manual Download Page 50

Page: 50 / 98

EKI-8500 Series User Manual

4.3.3

VLANs

4.3.3.1

Global VLAN Configuration

The function allows you to configure VLAN control settings.

Navigate to

Configuration

VLANs

and click

Configuration

Flow Control

If auto speed is selected on a port, this section indicates the flow

control capability that is advertised to the link partner, otherwise fixed-

speed is used if selected. The Current Rx column indicates whether

pause frames on the port are obeyed, and the Current Tx column

indicates whether pause frames on the port are transmitted. The Rx

and Tx settings are determined by the result of the last Auto

Negotiation setting.

Check a setting to use flow control. This setting is related to the

setting for Configured Link Speed.

Note: The 100FX standard doesn't support Auto Negotiation. In

100FX mode the flow control capabilities are shown as disabled.

PFC

When PFC (802.1Qbb Priority Flow Control) is enabled on a port flow

control on a priority level is enabled. Through the Priority field, range

(one or more) of priorities can be configured, e.g. '0-3,7' which equals

'0,1,2,3,7'. PFC is not supported through auto negotiation. PFC and

Flowcontrol cannot both be enabled on the same port.

Maximum Frame

Size

Enter the maximum frame size allowed for the switch port, including

FCS. The range is 1518-10240 bytes.

Excessive Collision

Mode

Configure the port transmit collision behavior.



Discard: Discard frame after 16 collisions (default).



Restart: Restart backoff algorithm after 16 collisions.

Frame Length Check Check an option to configure if frames with incorrect frame length in

the EtherType/Length field are to be dropped. An Ethernet frame

contains a field EtherType which can be used to indicate the frame

payload size (in bytes) for values of 1535 and below. If the EtherType/

Length field is above 1535, it indicates that the field is used as an

EtherType (indicating which protocol is encapsulated in the payload of

the frame). If frame length check is enabled and EtherType/Length

field doesn't match the actually payload length, frames with payload

size less than 1536 bytes are dropped. If frame length check is

disabled, frames are not dropped due to frame length mismatch.

Note: No drop counters count frames dropped due to frame length

mismatch

Save

Click

Save

to store the settings.

Reset

Click

Reset

to clear the settings.

Item

Description

Summary of Contents for EKI-8500 Series



































































































Search results

Summary of Contents for EKI-8500 Series

Reviews:

Related manuals for EKI-8500 Series

Brands by name

Popular brands

Advantech EKI-8500 Series, User Manual

Search results

Summary of Contents for EKI-8500 Series

Reviews:

Related manuals for EKI-8500 Series

Brands by name

Popular brands