Advantech-DLoG DLT-V83 Series Operating Instructions Manual Download Page 152

Page: 152 / 157

Guidelines and certificates

152 / 157

DLT-V83 Operating Instructions V2.00

WLAN special regulations for Germany and France

For the DLT-V83 with WLAN 802.11a/b/g/n, the following restrictions apply:

−

In Germany, WLAN 5 GHz band: 5.15 GHz – 5.35 GHz may only be used indoors.

−

In France, WLAN operation outdoors is only permitted in the 2454 – 2483.5 MHz range at max.

10 mW EIRP.

20.6.

Eco-design directive (2009/125/EC)

DLT-V83 Industrial Computers with an AC power supply unit meet the requirements of the Eco-design

directive (2009/125/EC), which prescribes environmentally friendly design for products involved in

energy consumption.

20.7.

CE marking

The devices of the DLT-V83 series were tested and fulfill the CE conformity requirements and carry the

CE mark on the rear side of the device.

20.8.

CCC, SRRC China

Several DLT-V83 models are CCC- and SRRC-certified and carry the respective mark on the device

label.

NOTICE

声明：此为

级产品，在生活环境中，该产品可能会造成无线电干扰，

在这种情况下，可能需要用户对其干扰采取切实可行的措施。

Summary of Contents for DLT-V83 Series






























































































































































Search results

Summary of Contents for DLT-V83 Series

Reviews:

Related manuals for DLT-V83 Series

Brands by name

Popular brands

Advantech-DLoG DLT-V83 Series, Operating Instructions Manual

Search results

Summary of Contents for DLT-V83 Series

Reviews:

Related manuals for DLT-V83 Series

Brands by name

Popular brands