Advantech-DLoG DLT-V83 Series Operating Instructions Manual Download Page 146

Page: 146 / 157

Malfunctions

146 / 157

DLT-V83 Operating Instructions V2.00

18.

Malfunctions

Error

Possible cause(s)

Remedy

Device does not boot

Are all plug connections connected

correctly?

Is the <Power> button / Ign

configuration correct?

Correct voltage ranges present?

Mouse pointer

position and

touchscreen touch

position do not match

If the deviation is large, recalibrate the

touchscreen.

AC devices: signal

transmission

problems with

connected devices

External electrical isolation of the

relevant lines recommended.

Battery pack run time

is significantly shorter

than specified.

The device may possibly

not be in the temperature

range which is necessary

for charging the battery

pack.

Check the temperature specifications for

the device and surroundings.

Maximum number of

charging cycles of the

battery pack has been

reached.

If temperature causes can be ruled out,

the battery pack has possibly reached

the maximum number of charging

cycles.

Replace the battery pack. Use only

original battery pack from Advantech.

No UPS functionality

although battery pack

is plugged in.

Battery pack is discharged

or deep discharged.

Charge the battery pack properly.

Observe

: If the battery pack is deep

discharged, the charging time can

increase by a multiple.

Nothing is shown on

the display,

Power LED does not

light up.

There is no voltage present

on the device.

Check the power switch, plug

connection, power supply cable and

fuse.

Ignition signal missing.

Check ignition cable and signal

Nothing is shown on

the display, Power

LED active.

Backlight is switched off.

Press backlight key ("light bulb"

symbol).

Brightness to low

Increase display brightness with key

Nothing is shown on

the display,

Temp LED active.

Operating temperature

limits

exceeded/undershot .

Wait until the device has cooled down

resp. warmed up.

Touchscreen reacts

imprecisely.

Device cannot be

operated by touch

input

Touchscreen is switched

off.

Press touchscreen on/off.

Touch driver error

Reinstall the touch driver or change

settings

Touchscreen is not

calibrated correctly.

The touchscreens is already calibrated

at the factory and therefore and does

usually not need to be recalibrated.

Summary of Contents for DLT-V83 Series






























































































































































Search results

Summary of Contents for DLT-V83 Series

Reviews:

Related manuals for DLT-V83 Series

Brands by name

Popular brands

Advantech-DLoG DLT-V83 Series, Operating Instructions Manual

Search results

Summary of Contents for DLT-V83 Series

Reviews:

Related manuals for DLT-V83 Series

Brands by name

Popular brands