Advantech-DLoG DLT-V83 Series Operating Instructions Manual Download Page 62

Page: 62 / 157

Operating the device

62 / 157

DLT-V83 Operating Instructions V2.00

9.4.4.

Operating states

Status of LEDs

DLT-V83 Status

Supply voltage

(green)

Temperature

(red)

OFF

Initial state, idle time – waiting for a new

ignition signal or for the <Power> key after

switch off; no voltage supply.

OFF

FLASHING

Temperature sensor malfunctioning.

FLASHING

OFF

DLT-V83 is in standby mode (S3).

OFF

Computer will only start if the temperature

the device

is in the range between -30 and

+62 °C again.

OFF

Computer start-up/normal operational

state/shutdown delay time.

Temperature < -30 or > +70 °C.

FLASHING

Temperature sensor malfunctioning.

Summary of Contents for DLT-V83 Series






























































































































































Search results

Summary of Contents for DLT-V83 Series

Reviews:

Related manuals for DLT-V83 Series

Brands by name

Popular brands

Advantech-DLoG DLT-V83 Series, Operating Instructions Manual

Search results

Summary of Contents for DLT-V83 Series

Reviews:

Related manuals for DLT-V83 Series

Brands by name

Popular brands