Adixen ACS 2000 User Manual Download Page 29

Page: 29 / 63

10/14

GB 03435 - Edition Edition 03 - October 09

A Commissioning
B Product

description

C Settings

D Test

mode

E RS232

mode

F Appendices

General settings for the

ACS 2000 controller

RS232 settings

Communication speed

Description

This setting is used to adjust the communication speed of the RS232
serial interface.
The speed is expressed in Baud units.

Accessing this setting:

Access:

SET/PROG2/4. BAUD

Modification of this setting does not require the controller to be
restarted.

Factory default setting:

The communication speed is factory set to

9600 bauds

Locking the settings

Description

This setting stops anyone modifying the configuration.

It is activated when the LOCK setting is ON.
“Err05” will appear anytime anyone tries to modify a setting.
See appendix 6: error messages).
To unlock the settings, set parameter lock to “

OFF

“

RS232 setting

Selecting the end of line characters for the RS232 transmission

CR (carriage return) = return to start of line only (with a risk of
overwriting the previous data).

CR LF (carriage line Feed) = advance to start of next line
(with no chance of overwriting the previously sent data).

Accessing this setting

Access:

SET/PROG2/7. RS232C

Factory default setting:

The controller is factory set to the

position.

㪧㪩㪦㪞㪄㩷㪉㩷

㪪㪧㩷

㪣㪦㪚㪢㩷

㪈

㪉

Accessing this setting:

Access:

SET/PROG2/5. PLOC

Modification of this setting does not require the controller to be
restarted.

Factory default setting

By default the controller is not locked: LOCK is factory set to “

OFF

“.

Summary of Contents for ACS 2000
































































Search results

Summary of Contents for ACS 2000

Reviews:

Related manuals for ACS 2000

Brands by name

Popular brands

Adixen ACS 2000, User Manual

Search results

Summary of Contents for ACS 2000

Reviews:

Related manuals for ACS 2000

Brands by name

Popular brands