Adixen ACS 2000 User Manual Download Page 26

Page: 26 / 63

GB 03435 - Edition Edition 03 - October 09

7/14

A Commissioning
B Product

description

C Settings

D Test

mode

E RS232

mode

F Appendices

Configuring the gauges

Specific settings

Capacitive gauge

(ASD 200X - ARD 200X)

Digit function

Description

This function shows or hides the 5th digit in the displayed pressure.

Activing the DIGIT function:

- Access:

SET/PROG1/16. DIGIT

- Press the

ENTER

button than on the button

Factory default setting

The switching function deactivated by default and the display set to

4 digits

Zero function

Description

This function allows you to assign a measured pressure value as a
datum point.
The values displayed will then be negative when the pressure is less
than the “ZERO” value entered.

Zero is displayed

Activing the ZERO function:

- Access:

SET/PROG1/7.OFS

Remark: this is only possible in the voltage range of –0.2V to +0.2V
delivered on the gauge’s analog output.

㪧㪩㪦㪞㪄㪈

㪉㪊

㪫㪜㪪㪫

㪞㪘㪬㪞㪜

㩷

㪪㪧㩷㪈㩷㪉

㪚㪦㪤㪤

㪧㪩㪦㪞㪄㪈

㪉㪊

㪫㪜㪪㪫

㪞㪘㪬㪞㪜

㩷

㪪㪧㩷㪈㩷㪉

㪚㪦㪤㪤

㪱㪜㪩㪦

Note : if the «ZERO» can’t be set, th «ERR09» message displays on the
screen for 2 seconds. (see Appendix 6 for the error message list).

Summary of Contents for ACS 2000
































































Search results

Summary of Contents for ACS 2000

Reviews:

Related manuals for ACS 2000

Brands by name

Popular brands

Adixen ACS 2000, User Manual

Search results

Summary of Contents for ACS 2000

Reviews:

Related manuals for ACS 2000

Brands by name

Popular brands