Adixen ACS 2000 User Manual Download Page 39

Page: 39 / 63

6/6

GB 03436 - Edition 02 - September 07

A Commissioning
B Product

description

C Settings

D Test

mode

E RS232

mode

F Appendices

Controller interface tests

Testing the front panel

buttons

Accessing this test

Access:

SET/8.CTRL

- Press

ENTER

button to confirm.

Press the various front panel buttons and check that the corresponding
names come up on the screen.

Ex:

—> Screen display : «UP»

Leaving this test

To leave this test and get back to the previous screen,

press and hold

down

the

button.

Testing the RS232 link

Use this test to check the data transfer to and from a computer.

Accessing this test

Access :

SET/9.232C

- Press

ENTER

button to confirm.

This screen displays ‘COMM’ while data being transmitted from the
computer to the controller.
The transmitted character is resent from the controller to the computer.

TEST

SP COMM

Leaving this test

Press the

button to get back to the previous screen.

Summary of Contents for ACS 2000
































































Search results

Summary of Contents for ACS 2000

Reviews:

Related manuals for ACS 2000

Brands by name

Popular brands

Adixen ACS 2000, User Manual

Search results

Summary of Contents for ACS 2000

Reviews:

Related manuals for ACS 2000

Brands by name

Popular brands