Acromag Vertu Series Instruction Manual Download Page 3

Page: 3 / 47

Vertu Series VPM3000 Process Meters & Temperature Transmitters

Instruction Manual

Table of Contents

Introduction ......................................................................................................... 6

Ordering Information .......................................................................................... 6

Specifications ..................................................................................................... 7

General ............................................................................................................ 7

Process Input .................................................................................................. 7

Temperature Inputs ........................................................................................ 7

Relays Option .................................................................................................. 8

Serial Communications .................................................................................. 8

Isolated 4-20 mA Transmitter Output ............................................................ 8

External Button Contacts ............................................................................... 8

Compliance Information..................................................................................... 9

Safety ............................................................................................................... 9

Electromagnetic Compatibility ...................................................................... 9

Safety Information .......................................................................................... 9

Installation........................................................................................................... 9

Unpacking ....................................................................................................... 9

Panel Mounting ............................................................................................. 10

Mounting Dimensions .................................................................................. 10

Connections .................................................................................................. 11

Connector Labeling ..................................................................................... 11

Power Connections ..................................................................................... 12

Signal Connections ..................................................................................... 12

Serial Communication ................................................................................. 13

Relays and 24 V Output Connections ......................................................... 14

Switching Inductive Loads ........................................................................... 14

4-20 mA Output & Input Signal Connections ............................................... 15

Isolated 4-20 mA Signal Splitters & Converters ......................................... 16

Isolated 4-20 mA Signal Splitter .................................................................. 16

4-20 mA to 0-10 VDC Signal Converter....................................................... 16

Setup and Programming .................................................................................. 17

Overview ........................................................................................................ 17

Front Panel Buttons and Status LED Indicators ........................................ 17

Display Functions and Messages ................................................................... 18

Main Menu ..................................................................................................... 19

Setting Numeric Values ................................................................................ 19

Setting Up the Meter (

setu

) .......................................................................... 19

Setting the Input Signal (

inpt

) .................................................................... 19

Setting the Decimal Point (

dc.pt

) ................................................................. 20

Setting the Temperature Scale (

F C

) ......................................................... 20

Programming the Meter (

prog

) .................................................................... 20

Scaling the Meter (

scal

) ............................................................................. 20

Calibrating the Meter (

Cal

) .......................................................................... 21

Recalibrating Temperature Inputs (

Cal

) ...................................................... 21

Recalibrating Process Inputs (

ICal

)............................................................ 21

Setting the Relay Operation (

rely

) ............................................................. 22

Relay and Alarm Operation ......................................................................... 23

Scaling the 4-20 mA Analog Output (

Aout

) ................................................. 27

Isolated 4-20 mA Signal Splitters & Converters ........................................... 27

Program the Sensor Break Output Value (

SEbr

) ......................................... 27

Analog Output when Display is Out of Range ............................................. 27

Setting Up the Password (

pass

) .................................................................. 28

Locking the Meter ........................................................................................ 28

Unlocking the Meter .................................................................................... 28

Summary of Contents for Vertu Series
















































Search results

Summary of Contents for Vertu Series

Reviews:

Related manuals for Vertu Series

Brands by name

Popular brands

Acromag Vertu Series, Instruction Manual

Search results

Summary of Contents for Vertu Series

Reviews:

Related manuals for Vertu Series

Brands by name

Popular brands