Acromag Vertu Series Instruction Manual Download Page 42

Page: 42 / 47

Vertu Series VPM3000 Process Meters & Temperature Transmitters

Instruction Manual

Troubleshooting Tips

This meter is a highly sophisticated instrument with an extensive list of features and capabilities. If the front panel but-

tons are used to program the meter, it may be a difficult task to keep everything straight. That is why we strongly rec-

ommend the use of the DisplayWizard software for all programming activities.

Symptom

Check/Action

No display at all

Check power at power connector

Not able to change setup or programming,

LoCd

is displayed

Meter is locked, enter correct four-digit password to unlock

Meter does not respond to input change

If a Low-Flow Cutoff Value has been programmed, the meter will

display zero below that point, regardless of the input – which can

appear like the meter is not responding to an input change.

Check to make sure the problem is not being caused by an

undesired low-flow cutoff value.

Meter displays error message during

calibration (

err

)

Check:

1. Signal connections
2. Input selected in

Setup

3. Minimum input span requirements

Meter displays

•

open

•

9999

•

-1999

•

Displays negative number, not

responding to RTD.

Check:

1. Input selected in

Setup

2. TC/RTD Switch position
3. Corresponding signal at Signal connector

Display alternates between

and a number

Press

Menu

to exit Max/Min

display readings.

Display response is too slow

Check filter and bypass values

Inaccurate temperature reading

Check:

1. Temperature units (

F or

2.  TC type or RTD curve selected
3.  Offset adjustment
4.  TC wire used
5.  Calibration

If the display locks up or the meter does

not respond at all

Cycle the power to restart the microprocessor.

Relay operation is reversed

Check:

1. Fail-safe in

Setup

2. Wiring of relay contacts

Relay and status LED do not

respond to signal

Check:

1. Relay action in

Setup

2. Set and reset points

Meter not communicating with

DisplayWizard or other programs

Check:

1.  Serial adapter and cable
2.  Serial protocol selected
3.  Meter address and baud rate
4.  DisplayWizard address and baud rate

Summary of Contents for Vertu Series
















































Search results

Summary of Contents for Vertu Series

Reviews:

Related manuals for Vertu Series

Brands by name

Popular brands

Acromag Vertu Series, Instruction Manual

Search results

Summary of Contents for Vertu Series

Reviews:

Related manuals for Vertu Series

Brands by name

Popular brands