Acromag Vertu Series Instruction Manual Download Page 44

Page: 44 / 47

Vertu Series VPM3000 Process Meters & Temperature Transmitters

Instruction Manual

Right

Arrow &

Menu

(or hold Menu for 3 sec)

Pushbutton

Function

Menu

Go to Programming Mode or leave Programming, Advanced

Features, and Max/Min Modes.

Right

Arrow

Move to next digit.

Arrow

Move to next selection or increment digit.

Enter/Ack

Accept selection/value and move to next selection.

Right

Arrow &

Menu

simultaneously enters Advanced Features

Max/Min Mode

While in Run Mode, pressing

Arrow will initiate Max/Min Mode.

Arrow

toggles between Max & Min displays, and

Right

Arrow resets the Max/Min to the

current value. Press

Menu

or wait 10 seconds to return to Run Mode. Pressing

Enter/Ack

will disable the 10 second timeout and continuously display Max or Min.

Press

Right

arrow and

Menu

to access Advanced Features

When the meter is locked, Adjust,

Filter and Bypass can only display

their settings, and the Copy and

ICAL functions are not available.

Adjust

Filter

Bypass

Serial

Copy

Send

TC or RTD?

Yes No

TC or RTD?

Yes No

Initial

Calibrate

Diagnostics

Select

Function

Cutoff

Output

Linear

Sq. Root

Address

TX Delay

Baud

Protocol

Parity

Modbus

PDC

Byte-to-byte

timeout

Modbus?

No Yes

Intensity

Program

Run

Max &

Min

Advanced

Features

Arrow

Menu

Operational Modes

Summary of Contents for Vertu Series
















































Search results

Summary of Contents for Vertu Series

Reviews:

Related manuals for Vertu Series

Brands by name

Popular brands

Acromag Vertu Series, Instruction Manual

Search results

Summary of Contents for Vertu Series

Reviews:

Related manuals for Vertu Series

Brands by name

Popular brands