Acromag Vertu Series Instruction Manual Download Page 2

Page: 2 / 47

Vertu Series VPM3000 Process Meters & Temperature Transmitters

Instruction Manual

Disclaimer

The information contained in this document is

subject to change without notice. Acromag Inc

makes no representations or warranties with

respect to the contents hereof and specifically

disclaims any implied warranties of merchantability

or fitness for a particular purpose. See Warranty

Information and Terms & Conditions on

www.acromag.com

for complete details.

•

Read complete instructions prior to installation

and operation of the meter.

•

Risk of electric shock or personal injury.

•

This product is not recommended for life support

applications or applications where malfunctioning

could result in personal injury or property loss.

Anyone using this product for such applications

does so at his/her own risk. Acromag Inc shall

not be held liable for damages resulting from

such improper use.

WARNING

Cancer and Reproductive Harm -

www.P65Warnings.ca.gov

Limited Warranty

Acromag Inc warrants this product against defects

in material or workmanship for the specified period

under “Specifications” from the date of shipment

from the factory. Acromag Inc’s liability under this

limited warranty shall not exceed the purchase

value, repair, or replacement of the defective unit.

See Warranty Information and Terms & Conditions

www.acromag.com

for complete details.

Registered Trademarks

All trademarks mentioned in this document are

the property of their respective owners.

FREE DisplayWizard

Programming Software

Note:

Vertu meter is not powered from USB connection and

requires external power to be programmed.

DisplayWizard software is intuitive, and most customers

can get their meter programmed as they like without

even looking in the manual.
In addition to programming, the software, with

additional devices, may be used for:

•

Monitoring up to 100 Vertu meters

•

Datalogging using your PC

•

Generating and saving programming files for

later use

Once your meter is programmed the way you want it,

you can wire it up for your application per the

instructions in this manual and install it. If you find that

you need to make adjustments to the programming

after the meter is installed, you can use the front panel

buttons and the instructions in this manual to do so.

Summary of Contents for Vertu Series
















































Search results

Summary of Contents for Vertu Series

Reviews:

Related manuals for Vertu Series

Brands by name

Popular brands

Acromag Vertu Series, Instruction Manual

Search results

Summary of Contents for Vertu Series

Reviews:

Related manuals for Vertu Series

Brands by name

Popular brands