Acromag Vertu Series Instruction Manual Download Page 40

Page: 40 / 47

Vertu Series VPM3000 Process Meters & Temperature Transmitters

Instruction Manual

Troubleshooting

Due to the many features and functions of the meter,

it’s possible that the setup of the meter does not

agree with what an operator expects to see. If the

meter is not working as expected, refer to the

Diagnostics

menu and consult the recommendations

described below.

Diagnostics Menu (

diag

)

The

Diagnostics

menu is located in the

Advanced

Features Menu

, to access

Diagnostics

menu see

Advanced Features Menu

, page

It provides an easy way to view the programmed

parameter settings for troubleshooting purposes.

Press the

Enter/Ack

button to view the settings and

the

Menu

button to exit at any time.

For a description of the diagnostics messages

see

Advanced Features Menu & Display Messages

page

Determining Software Version

To determine the software version of a meter:

1. Go to the

Diagnostics

menu (

diAG

) and

press

Enter/Ack

button.

2. Press

arrow/

Max

button and scroll to

Information menu (

Info

3. Press

Enter/Ack

to access the software

number (

SFT

), version (

UER

). Write down the

information as it is displayed. Continue

pressing

Enter/Ack

until all the information

is displayed.

Reset Meter to Factory Defaults

When the parameters have been changed in a way

that is difficult to determine what’s happening, it might

be better to start the setup process from the factory

defaults.

Instructions to load factory defaults:

1. Enter the

Advanced

Features Menu

. See

Advanced Features Menu

, page

2. Press

arrow to go to

Diagnostics

3. Press and hold

Right

arrow/Reset for five

seconds, press

Enter/Ack

when display

flashes

reset

Note: If

Enter/Ack

is not pressed within

three seconds, display returns to

Diagnostics

menu.

4. The meter goes through an initialization

sequence (same as on power-up) and loads

the factory default settings.

Summary of Contents for Vertu Series
















































Search results

Summary of Contents for Vertu Series

Reviews:

Related manuals for Vertu Series

Brands by name

Popular brands

Acromag Vertu Series, Instruction Manual

Search results

Summary of Contents for Vertu Series

Reviews:

Related manuals for Vertu Series

Brands by name

Popular brands