manualshive.com logo in svg

Accutrol Apex Premier, Installation, Operation & Maintenance Manual, Page: 11 / 61

Share
Download
Accutrol Apex Premier Installation, Operation & Maintenance Manual Download Page 11

                                                                                                          T-APM - Apex Premier F

UME 

H

OOD 

M

ONITOR 

 

  T-APM                          0133MAN00015 - Rev J                      ECN  -                       JUL 2017                     

Page 11 of 61

 

Electrical Connections 

 
The steps to correctly wire the APM are as follows; reference Appendix C for proper wiring techniques 
and Appendix E for all electrical specifications of the APM. 

Step 1: Power 

For 24 VAC Control Power 

– On the back of the APM enclosure, remove the 2-position green terminal 

block labeled POWER INPUT.  Loosen the two screws and insert power wires and tighten screws.  

Caution:  O

bserve proper polarity when wiring multiple APM’s to the same 24 VAC transformer.

  

Always connect the HOT 24 VAC power lead to the power (+) terminal, and the neutral lead to the 
power (-) terminal.  Damage to the APM may result if wired improperly and will void the warranty

.    

 
For wall pluggable power cable 

– plug the optional power cube into an acceptable 120 VAC power outlet.  

Connect the power terminal block to the power input on the rear of the APM.  

Step 2: Digital Inputs 

Per job requirements, connect the device sending the unoccupied or external alarm dry contact closure 
between Digital Input 1 or 2 and the common terminal.  The digital inputs are software configurable to 
handle either input.  The digital inputs are actuated by a dry contact closure to common, maximum 
contact resistance is 1000 ohms.   

Step 3: Relay Outputs 

The APM has two independent relay outputs available.  Each relay is rated for a maximum of ½ A at 
120VAC or 1A at 30Vdc.  These relays are typically used to communicate fume hood Alarms to the 
Building Management System and send a Purge command to the fume hood exhaust controller.  Through 
software configuration, each relay output can be set to operate as either normally closed or normally 
open.  With no power applied to the APM, Relay 1 fails to a normally open position, while Relay 2 fails to 
a normally closed position. 

 
Note:  If the APM has been ordered from the factory with the optional Analog Output, Relay 1 is rated for 
a maximum of 5A at 250VAC or 30VDC and fails normally open.  Relay 2 remains the same as stated 
above.  Reference Appendix C for all APM specifications

. 

Step 4: (Optional) Analog Output 

The Analog Output is only available if ordered from the factory as an option.  

The APM’s Analog Output is 

software selectable (from 0 to 10Vdc in 0.1Vdc steps) and is proportional to the indicated face velocity 
displayed.  Connect the Analog Output positive terminal to the positive input terminal of the monitoring 
device and connect the Analog Output the ground terminal to the negative terminal of the monitoring 
device. 

Summary of Contents for Apex Premier






























































Reviews:

No comments