background image

EXC-500 MICROSCOPE SERIES 

ACCU-SCOPE

®

 

73 Mall Drive, Commack, NY  11725  •  631-864-1000  •  www.accu-scope.com 

2

5

MAINTENANCE 

Please remember to 

never

 

leave the microscope with any of the objectives or eyepieces removed and 

always protect the microscope with the dust cover when not in use. 

SERVICE 

ACCU-SCOPE

 ®

 microscopes are precision instruments which require periodic servicing to keep them 

performing properly and to compensate for normal wear. A regular schedule of preventative maintenance 

by qualified personnel is highly recommended. Your authorized ACCU-SCOPE

 ®

 distributor can arrange 

for this service. Should unexpected problems be experienced with your instrument, proceed as follows: 

1. Contact the ACCU-SCOPE

 ®

 distributor from whom you purchased the microscope. Some

problems can be resolved simply over the telephone. 

2. If it is determined that the microscope should be returned to your ACCU-SCOPE

 ®

 distributor or to

ACCU-SCOPE

 ®

 for warranty repair, pack the instrument in its original Styrofoam shipping carton. If you 

no longer have this carton, pack the microscope in a crush-resistant carton with a minimum of three 

inches of a shock absorbing material surrounding it to prevent in-transit damage. The microscope should 

be wrapped in a plastic bag to prevent Styrofoam dust from damaging the microscope. Always ship the 

microscope in an upright position; 

NEVER SHIP A MICROSCOPE ON ITS SIDE

. The microscope or 

component should be shipped prepaid and insured. 

LIMITED MICROSCOPE WARRANTY

This microscope and its electronic components are warranted to be free from defects in material and workmanship 

for a period of five years from the date of invoice to the original (end user) purchaser.  The LED lamp is warranted 
for a period of two years from the date of invoice to the original (end user) purchaser.  This warranty does not cover 

damage caused in-transit, misuse, neglect, abuse or damage resulting from improper servicing or modification by 

other  then  ACCU-SCOPE  approved  service  personnel.    This  warranty  does  not  cover  any  routine  maintenance 

work or any other work, which is reasonably expected to be performed by the purchaser. Normal wear is excluded 

from  this  warranty.  No  responsibility  is  assumed  for  unsatisfactory  operating  performance  due  to  environmental 
conditions such as humidity, dust, corrosive chemicals, deposition of oil or other foreign matter, spillage or other 

conditions  beyond  the  control  of  ACCU-SCOPE  INC.    This  warranty  expressly  excludes  any  liability  by  ACCU-

SCOPE INC. for consequential loss or damage on any grounds, such as (but not limited to) the non-availability to 

the End User of the product(s) under warranty or the need to repair work processes.  Should any defect in material, 

workmanship or electronic component occur under this warranty contact your ACCU-SCOPE distributor or ACCU-
SCOPE at (631) 864-1000.  This warranty is limited to the continental United States of America.  All items returned 

for warranty repair must be sent freight prepaid and insured to ACCU-SCOPE INC., 73 Mall Drive, Commack, NY  

11725 – USA.  All warranty repairs will be returned freight prepaid to any destination within the continental United 

States  of  America,  for  all  foreign  warranty  repairs  return  freight  charges  are  the  responsibility  of  the 

individual/company who returned the merchandise for repair.  

ACCU-SCOPE is a registered trademark of ACCU-SCOPE INC., Commack, NY 11725 

Summary of Contents for EXC-500


























Reviews: