background image

25

www.acclaimlighting.com

LIMITED PRODUCT WARRANTY

A. Acclaim Lighting™ hereby warrants, to the original purchaser, Acclaim Lighting finished products 

to be free of manufacturing defects in material and workmanship for a standard period of:

 

Fixtures:  

5 Years (1,825 days) from the date of purchase.

 

Drivers, power supplies and accessories:   5 Years (1,825 days) from the date of purchase.

 

Flex Products:  

3 Years (1,095 days) from the date of purchase.

 

Controllers:  

2 Years (730 days) from the date of purchase.

It is the owner’s responsibility to establish the date and place of purchase and warranty 

terms by acceptable evidence, at the time service is sought.
B. For warranty service, send the product only to the Acclaim factory. All shipping charges 

must be pre-paid. If the requested repairs or service (including parts replacement) are 

within the terms of this warranty, Acclaim Lighting will pay return shipping charges only 

to a designated point within the United States. If the entire instrument is sent, it must be 

shipped in its original package. No accessories should be shipped with the product. If any 

accessories are shipped with the product, Acclaim Lighting shall have no liability whatsoever 

for loss of or damage to any such accessories, nor for the safe return there of.  Acclaim 

reserves the right to replace the item with same or similar product at its discretion.
C. This warranty is void if the serial number has been altered or removed; if the product is 

modified in any manner which Acclaim concludes, after inspection, affects the reliability of 

the product; if the product has been repaired or serviced by anyone other than the Acclaim 

Lighting factory unless prior written authorization was issued to purchaser by Acclaim 

Lighting; if the product is damaged because not properly maintained as set forth in the 

instruction manual.
D. This is not a service contract, and this warranty does not include maintenance, cleaning 

or periodic check-up nor do we guarantee as part of this warranty any lumen performance 

during period. Parts not covered by this warranty include: fuses, external power supplies, 

third party items not manufactures by Acclaim lighting. During the period specified above, 

Acclaim Lighting will replace defective parts at its expense, and will absorb all expenses 

for warranty service and repair labor by reason of defects in material or workmanship. The 

sole responsibility of Acclaim Lighting under this warranty shall be limited to the repair 

of the product, or replacement thereof, including parts, at the sole discretion of Acclaim 

Lighting. At no time will installation or re-installation or products labor or liability costs will 

be assumed by Acclaim Lighting. All products covered by this warranty were manufactured 

after January 1, 2012, and bear identifying serial number marks to that effect.
E. Acclaim Lighting reserves the right to make changes in design and/or improvements 

upon its products without any obligation to include these changes in any products 

theretofore manufactured No warranty, whether expressed or implied, is given or made 

with respect to any accessory supplied with products describe above. Except to the extent 

prohibited by applicable law, all implied warranties made by Acclaim Lighting in connection 

with this product, including warranties of merchantability or fitness, are limited in duration 

to the warranty period set forth above. And no warranties, whether expressed or implied, 

including warranties of merchantability or fitness, shall apply to this product after said 

period has expired. 
F. Marine or extreme weather location applications using Acclaim lighting products are 

subject to a 2 year limited warranty and Acclaim must be notified prior to delivery of units 

for such applications so that preventative treatment can be made to the products to ensure 

proper performance and product life with a special marine code coating / sealing process at 

an additional cost. 
G. The consumer’s and or dealer’s sole remedy shall be such repair or replacement as is 

expressly provide above; and under no circumstances shall Acclaim Lighting be liable for 

any loss or damage, direct or consequential, arising out of the use of, or inability to use, 

this product. This warranty is the only written warranty applicable to Acclaim Lighting 

products and supersedes all prior warranties and written descriptions of warranty terms and 

conditions heretofore published.

Summary of Contents for Linear XTR





























Reviews: