Ablerex EnerSolis Series User Manual Download Page 71

Page: 71 / 77

Table 2 Converter Failure and Grid System Error Code Descriptions

Code

Cause

Description

Troubleshooting instructions

Er00

DC_BUS charging error

During the converter DC turn-on
procedure, DC_BUS has failed to

reach the preset value

1. Disconnect the solar panel array

and the AC grid from the converter.

2. Wait for all LEDs to be completely

off, and then re-connect the solar
panel array and the AC grid to the

converter.

3. If the error continues to occur,

please contact the supplier.

Er07

DC_BUS voltage too
high

DC_BUS operating voltage higher
than the preset value

Er08

DC_BUS voltage too low

DC_BUS operating voltage lower

than the preset value

Er17

Main control board

memory error

Controller configuration value

error

Er22

Output relay error

Relay error during the converter
AC turn-on procedure

Er24

Output

current

detection error

Output current error during the

converter DC turn-on procedure

Er25

Maximum power point

tracker

input

overcurrent

Maximum power point tracker

input current over the rated value

Er26

Maximum power point

tracker

input

overcurrent

Er45

Maximum power point
tracker

input

overcurrent

Er46

Maximum power point

tracker

input

overcurrent

Er48

Converter driver error

Converter IGBT error

Disconnect the solar panel array and

the AC grid from the converter.
Please contact the supplier.

Er49

Converter

driver

overcurrent

Converter output current over the

rated value

Er50

Converter driver voltage
insufficient

Converter IGBT error or current
error

Er51

Maximum power point

track A&B driver error

Maximum power point track IGBT
error

Disconnect the solar panel array and

the AC grid from the converter.
Please contact the supplier.

Er52

Maximum power point

tracker C&D driver error

Er53

Maximum power point
tracker A&B driving

voltage insufficient

Maximum power point tracker
IGBT error or current error

Er54

Maximum power point

tracker C&D driving

voltage insufficient

Summary of Contents for EnerSolis Series














































































Search results

Summary of Contents for EnerSolis Series

Reviews:

Related manuals for EnerSolis Series

Brands by name

Popular brands

Ablerex EnerSolis Series, User Manual

Search results

Summary of Contents for EnerSolis Series

Reviews:

Related manuals for EnerSolis Series

Brands by name

Popular brands