Transmitting Results Wirelessly to
the Data Management System
Note 1: Users must follow site specific guidelines for operating wireless devices.
Note 2: Handheld must remain at leas
t 20 cm (approx. 8 inches) from the body (head and
torso) when the radio is on. The radio is on:
• whenever the handheld is transmitting,
• when an operator is using the Wireless Utility Menu, and
• during the 2 minutes following a test cycle.
Note 3: All analyzers shipped beginning in 2015 contain
Wireless Module FCC ID:
YOPGS1500M (Firmware: GEXPSX.X.X/MCUX.X)
, and the SNR value is not
available. The SNR field will display “SNR: --dB.”
Users may transmit results wirelessly to the data management system:
• directly following an individual test cycle using the Test Options Menu , or
• on-demand using the Transmit Data menu.
A. To transmit data wirelessly from the handheld directly following a test cycle:
1. When newly generated test results appear on the handheld display,
press (Test Options).
2. Press (Transmit Data). A “Waiting to Send”
message will appear on the display screen.
Additionally, the “State” line toward the middle of the
screen may display a series of messages as shown
below, or indicate that it is connected.
• Off: wireless module is off
• Booting: loading software on wireless module
• Joining: attempting to join the network
• Associated: The module successfully joined the
network, associated with an Access Point and
has been granted permission to communicate
to the network
• Connected: connected to the data manager
3. Once the
Connected
state is reached, a
“Communication in Progress” message will appear
at the top of the screen. When this message
disappears and the display returns to the
Test Menu, the transmission is successful.
Note:
If there are unsent results remaining in the handheld
at the completion of a transmission attempt, a
“Communication Ended” message will appear on the
handheld indicating how many unsent results are left.
B. To transmit data wirelessly from the handheld
on-demand using the Transmit Data menu:
1. Press the key on the handheld.
2. Press the key.
3. Press (Transmit Data). Press a number key
to select the data set you would like to transmit.
4. A “Waiting to Send” message will appear on the
display screen.
Additionally, the “State” line toward the middle of the
screen may display a series of messages as shown
below, or indicate that it is connected.
• Off: wireless module is off
• Booting: loading software on wireless module
• Joining: attempting to join the network
• Associated: the module successfully joined the
network, associated with an Access Point and
has been granted permission to communicate
to the network
• Connected: connected to the data manager
5. Once the
Connected
state is reached, a
“Communication in Progress” message will appear
at the top of the screen. When this message
disappears and the display returns to the
Administration Menu, the transmission is successful.
Note:
If there are unsent results remaining in the handheld
at the completion of a transmission attempt, a
“Communication Ended” message will appear on the
handheld indicating how many unsent results are left.
Waiting
To Send
Status
State: Connected
Signal: Strong
-45dBm
SNR: 50dB
1 - Cancel
Transmit Data
1 - Most Recent
2 - This Month
3 - Last Month
4 - All
5 - Unsent
Communication
In Progress
Status
State: Connected
Signal: Strong
-45dBm
SNR: 50dB
1 - Cancel
Waiting
To Send
Status
State: Connected
Signal: Strong
-45dBm
SNR: 50dB
1 - Cancel
Communication
In Progress
Status
State: Connected
Signal: Strong
-45dBm
SNR: 50dB
1 - Cancel
MENU
10
11
1
6
4
Communication
Ended
Unsent: 4
Communication
Ended
Unsent: 4
See Note 3.
See Note 3.
See Note 3
on page 10.
