ABB IRB 7600 Series Product Manual Download Page 407

Page: 407 / 480

5 Calibration information

5.2. Calibration methods

405

3HAC022033-001 Revision: K

rig

t 200

201

1 AB

B. All

ts reser

ed.

Calibration methods

Each calibration method is detailed in a separate manual. Following is a brief description of

the methods available.

Calibration Pendulum - standard method

Calibration Pendulum is the standard method for calibration of all ABB robots (except IRB

6400R, IRB 640, IRB 1400H, and IRB 4400S) and is also the most accurate method for the

standard type of calibration. It is the recommended method in order to achieve proper

performance.

Two different routines are available for the Calibration Pendulum method:

•

Calibration Pendulum II

•

Reference calibration

The calibration equipment for Calibration Pendulum is delivered as a complete toolkit,

including the operating manual for

Calibration Pendulum

, which describes the method and

the different routines further.

Levelmeter calibration - alternative method

Levelmeter calibration is referred to as the alternative method for calibration of ABB robots

because of the less accurate values obtained during calibration. The method uses the same

principles as Calibration Pendulum, but does not have as good of mechanical tolerances to

the toolkit parts as the standard method with Calibration Pendulum.

This method may, after calibration, require modifications in the robot program and is

therefore not recommended.

The calibration equipment for Levelmeter Calibration is ordered as separate parts for each

robot and the operating manual for

Levelmeter calibration

is enclosed with the Levelmeter

2000.

CalibWare - absolute accuracy calibration

To achieve a good positioning in the Cartesian coordinate system, absolute accuracy

calibration is used as a TCP calibration. The CalibWare tool guides through the calibration

process and calculates new compensation parameters. This is further detailed in the

application manual

Absolute accuracy calibware field 5.0

If a service operation is done to a robot with absolute accuracy, a new absolute accuracy

calibration is required in order to establish full performance. For most cases after motor and

transmission replacements that do not include taking apart the robot structure, standard

calibration is sufficient. Standard calibration also supports wrist exchange.

References

Article numbers for the calibration tools are listed in the section

Special tools on page 428

The calibration equipment for Calibration Pendulum is delivered as a complete toolkit,

including

Operating manual - Calibration Pendulum

, which describes the method and the

routines further.

Continued

工控帮助教小舒QQ2823408167

长沙工控帮教育科技有限公司

Summary of Contents for IRB 7600 Series

























































































































































































































































































































































































































































































Search results

Summary of Contents for IRB 7600 Series

Reviews:

Brands by name

Popular brands

ABB IRB 7600 Series, Product Manual

Search results

Summary of Contents for IRB 7600 Series

Reviews:

Brands by name

Popular brands