ABB i-bus KNX Yucus YUB/U1.0.1 Series Technical Reference Manual Download Page 36 | Manualshive

Page: 36 / 173

background image

KNX Technical Reference Manual
ABB i-Bus

®

KNX Yucus

35

12.5.3 Common parameter – Energy saving object
Options

Deactivated
Activated

This 1-bit communication object can be associated with the following:

1. Energy saving state (Energy saving mode, common parameter). If an ON telegram

was receive, LCD display will be in bright illumination, if an OFF telegram was
received, LCD display will be in dark illumination.

2. Energy saving state with “Deactivate/activate LCD display” (1= LCD backlight on /

0 = LCD Backlight off) activate. If an ON telegram was receive, LCD display will
be in bright illumination, if an OFF telegram was received, LCD display will be off.

12.5.4 Common parameter – LCD backlight brightness in Energy saving function
Options

Off
Minimum
Dark

This parameter is used to specify the brightness of LCD display when control element
have energy saving mode activate after non-actuation of the control element.

12.5.5 Common parameter – LCD backlight orientation in night mode
Options

Deactivated
Activated

This parameter is used to specify whether will there be an orientation backlight when
control element enter into night mode.

12.5.6 Object no
Object name

Data type

Flags

LCDBL: LCD backlight sleep
mode GO

1 bit DPT 1.001

C, W, U

LCDBL: Day/Night mode

1 bit DPT 1.001

C, W, U

LCDBL: Energy saving object 1 bit DPT 1.001

C, W, U

12.6

Application “LCD display sub display”

For 3/6 gang, 4/8 gang, RTC and RTC with 2/4 gang version. The control element has an
option to display additional information that is obtain from the KNX bus line.

12.6.1 Common parameter – Sub display selection
Options

Inactive
Actual temperature
Humility
Pm2.5
VOC
CO2
Time

«
...
34
35
36
37
38
...
»

Summary of Contents for i-bus KNX Yucus YUB/U1.0.1 Series














































































































































































Reviews:

No comments

Related manuals for i-bus KNX Yucus YUB/U1.0.1 Series

Brand: Eastern Times Technology Pages: 4

Brand: Vacon Pages: 18

Brand: Viking Pages: 4

SR-ZG9001T-RGBW

Brand: Sunricher Pages: 3

Brand: Kong Pages: 2

Ratio Feeder J+ Advanced Series

Brand: H.E. Anderson Pages: 11

Brand: LAUNDRY SOLUTION Pages: 14

Brand: SFC Pages: 48

Brand: Satel Pages: 8

Brand: R-Tec Pages: 14

Brand: NaturalPoint Pages: 2

Brand: Samson Pages: 64

Brand: SystemAir Pages: 4

Automation PC 620

Brand: B&R Pages: 594

Brand: SLV Pages: 12

Brand: AC Infinity Pages: 20

FibreBridge 7500

Brand: ATTO Technology Pages: 2

Brand: SE Controls Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands