ABB i-bus KNX Yucus YUB/U1.0.1 Series Technical Reference Manual Download Page 31

Page: 31 / 173

KNX Technical Reference Manual
ABB i-Bus

KNX Yucus

When device locking is selected, 1 bit communication object will be available. It is used
to control the locking function of the complete device.

12.2.5 Common parameter – Manual lock / unlock by pressing switch button pair
Options

Yes
No

This parameter is used to specify whether the function locking or device locking function
can be manually lock / unlock pressing physical rocker button for a define time period

Note: This parameter is only visible if “Locking function selection” is activated.

12.2.6 Common parameter – Lock / unlock device by pressing button pair
Options

Button 1-2
Button 3-4
Button 5-6
Button 7-8

This parameter is used to specify which switch button pair to press to lock / unlock the
device locking function

Note: This parameter is only visible if “Manual lock / unlock by pressing switch

button pair” is activated.

12.2.7 Common parameter – Time for pressing the button pair to lock / unlock
Options

Time input from 1 sec to 10 sec

This parameter is used to specify the time duration to press on the button pair to lock /
unlock the device locking function.

Note: This parameter is only visible if “Manual lock / unlock by pressing switch

button pair” is activated.

12.2.8 Objects no
Object name

Data type

Flags

GS: Send in Operation

1 Bit DPT 1.001

C, T

12.3

Application “Device locking function”

When device locking is selected in locking function selection. It is used to control the
locking function of the complete device.

Summary of Contents for i-bus KNX Yucus YUB/U1.0.1 Series














































































































































































Search results

Summary of Contents for i-bus KNX Yucus YUB/U1.0.1 Series

Reviews:

Related manuals for i-bus KNX Yucus YUB/U1.0.1 Series

Brands by name

Popular brands

ABB i-bus KNX Yucus YUB/U1.0.1 Series, Technical Reference Manual

Search results

Summary of Contents for i-bus KNX Yucus YUB/U1.0.1 Series

Reviews:

Related manuals for i-bus KNX Yucus YUB/U1.0.1 Series

Brands by name

Popular brands