ABB i-bus KNX Yucus YUB/U1.0.1 Series Technical Reference Manual Download Page 69 | Manualshive

Page: 69 / 173

background image

KNX Technical Reference Manual
ABB i-Bus

®

KNX Yucus

68

12.20.4

Common parameter – Value 2

Options

–

1 bit

: On/Off

–

1 byte 0 - 100%:

(0%-100%)

–

1 byte 0 - 255

: 0 to 255

–

2-byte float

: -671088.64 to 671088.64

–

2-byte signed

: -32768 to +32767

–

2-byte unsigned

: 0 to 65,535

–

4-byte float

: -4000000 to 4000000

–

4-byte signed:

-2147483648 to 2147483647

–

4-byte unsigned

: arbitrary values from 0 to

4294967295

Value 2 options are dependent on the setting of the "Object type" parameter.

1 bit

: switching functions (e.g. On/Off, enable/blocked, true/untrue)

–

1 bit

: switching functions (e.g. On/Off, enable/blocked, true/untrue)

–

1 byte 0 - 100%:

percentage values (0 = 0%, 255 = 100%)

–

1 byte 0 - 255

: arbitrary values from 0 to 255

–

2-byte float

: floating point value (physical values such as temperature or brightness) -

671088.64 to 671088.64
–

2-byte signed

: arbitrary values from -32768 to +32767

–

2-byte unsigned

: arbitrary values from 0 to 65,535

–

4-byte float

: floating point value (physical values) -4000000 to 4000000

–

4-byte signed:

arbitrary values from -2147483648 to 2147483647

–

4-byte unsigned

: arbitrary values from 0 to 4294967295

12.20.5

Object no

Object name

Data type

Flags

Value switching

1 bit DPT 1.001

C, W, T, U

Value switching

1 byte DPT 5.001

C, W, T, U

Value switching

1 byte DPT 5.010

C, W, T, U

Value switching

2 byte DPT 9.xxx

C, W, T, U

Value switching

2 byte DPT 8.001

C, W, T, U

Value switching

2 byte DPT 7.001

C, W, T, U

Value switching

4 byte DPT 14.xxx

C, W, T, U

Value switching

4 byte DPT 13.001

C, W, T, U

Value switching

4 byte DPT 12.001

C, W, T, U

12.21

Application “2-button value dimming sensor”

With the "2-button value dimming sensor" application, it is possible to send 1-byte value
telegrams via an operation of the rocker. Each operation of the left or right side of the
rocker will increase or reduce a 1-byte value (percent or value from 0 to 255). The 1-byte
value can be connected with 1-byte brightness value objects of dimming actuators. This
allows a dimming actuator to be dimmed brighter or darker with the rocker via value
telegrams.

12.21.1

Common parameter – Object type

Options

1 byte 0 - 100%

«
...
67
68
69
70
71
...
»

Summary of Contents for i-bus KNX Yucus YUB/U1.0.1 Series














































































































































































Reviews:

No comments

Related manuals for i-bus KNX Yucus YUB/U1.0.1 Series

Brand: D-Link Pages: 40

Brand: Raypak Pages: 24

Brand: J+J Pages: 91

Brand: Vacon Pages: 132

Brand: Thermomart Pages: 6

Brand: Oilon Pages: 74

Brand: W.E.ST. Pages: 34

Brand: Zamel Pages: 2

Brand: EP Solar Pages: 3

Brand: Danfoss Pages: 36

Brand: Elmo Pages: 30

Brand: Integra Pages: 17

Brand: Kohler Pages: 2

Brand: FlyDigi Pages: 12

Brand: Sensor Access Pages: 11

Brand: Wecon Pages: 12

Brand: K-Tech Pages: 2

Brand: DSE Pages: 100

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands